Seeing blue chickens? Do not adjust your monitor. Cerulean poultry are a perfectly normal story time occurrence.
We read Blue Chicken by Deborah Freedman (Penguin, 2011). An illustration of a barnyard sits on a drawing board. It’s almost finished – until a white chicken gets loose from the page and tips over a pot of blue ink! Now, nothing looks right. The ducks are no longer yellow, the pansies are no longer purple, and the other farm animals are totally peeved. Luckily, a dash of water will set things right!
To celebrate that adventurous blue chicken, we made some box birds, cozy nests, and then headed outside for a multi-color egg hunt!
You’ll need:
- A long strip of white poster board (approximately 2.25″ x 22″)
- A sturdy, 7″ paper plate
- 1 box ( mine was 4.5″ x 4.5″ x 6″ – a small tissue box works too!)
- Blue, white, yellow, and brown construction paper
- A pair of wiggle eyes
- 9-12 small feathers, blue of course!
- 4-6 plastic eggs
- Stapler, scissors, tape and glue for construction
- Hot glue
We’ll begin with the nest (which is a replica of the nest from this egg beauty contest). Circle a strip of white poster board around the outside of a paper plate and staple it securely (you’ll need to remove the circle from around the plate to staple it properly).
Slide the paper plate back inside the circle, pushing it all the way to the bottom.
Now flip the “nest” over and use tape to reinforce the connection between the plate and the circle. I used at least 4 pieces of tape:
I also reinforced the inside connection with a ring of hot glue.
Finally, decorate your nest with uneven and crinkled strips of brown construction paper. Attach the strips to the nest with tape and/or glue.
Set the nest aside, it’s time for the chicken!
Wrap a box with blue construction paper. Glue a pair of yellow paper feet on the bottom, and blue paper wings on either side. Make a red paper cone beak, and hot glue it to the front of the box. Add a pair of wiggle eyes, or simply draw the eyes on with markers. Glue or tape feathers to the wings (add tail feathers to the rear if desired). Use red paper to make a comb for your chicken’s head. Then tab it and glue or tape it to the top of the box.
When the chickens were done, we headed outside to the library’s plaza, where we had hidden a bunch of plastic eggs. We told the kids they needed to find 5 eggs each, then shouted “1-2-3 Go!” To insure success, we tried to make the hiding places fairly obvious (and even held a few back to drop right in front of the kids while they were hunting):
You might recognize that ornate door from this post. It’s actually one of the side doors of the University Chapel, which shares the plaza with my library. If you’d like to take your eggs home in style, consider adding some blue paper crinkle to the nest. Awwww…so cute…now why does this make me think of marshmallow Peeps?
Every writer needs a pencil, and at the end of that pencil is…an eraser. By why settle for the cylindrical pink variety when you can opt for a colorful, unique creation of your own imagination? Enter the Creatibles D.I.Y. Eraser Kit, which retails for around $12. The kit includes a rainbow assortment of clay colors that you can sculpt and bake into custom erasers.
Our kid tester, Hope, is taking a break to tackle middle school madness (classes, school play, going to regionals for the National History Day competition…go Hope!), so Marissa took the Creatibles Kit for a test drive. Take it away, Marissa!
When working on my first eraser, I was conservative in my design and how much clay I used. I didn’t think there would be enough (each color is only 0.63 ounces). But I soon realized that I didn’t need that much (unless you’re making a gigantic multi-color dinosaur). The more comfortable I became with the clay, the more I experimented with detail and size.
Some of the colors (like black, green, and blue) will rub off on your hands and table. So it’s a good idea to wash your hands in between colors. Also, use parchment paper. It really helps keep clay residue off your work table.
When adding little detailed pieces to your erasers, make sure you stick the pieces on well! I had a few eyes and limbs fall off because I didn’t press them down hard enough. Eventually, I used a plastic knife for pressing. Clay modeling tools would probably help and look cleaner, but you don’t have to get that fancy – a plastic knife works fine!
The erasers need to bake at 210-250 degrees for 30 minutes (I went with 250 degrees) then cool and set for 1 hour. I used parchment paper to protect my cookie sheet as well. The hardest part of this project? Waiting the full hour while the erasers cooled down and hardened! I kept checking them every 15 minutes (and if you poke them and they haven’t set, you run the risk of leaving a fingerprint or losing small pieces).
And they work! The pencil residue will stick to the erasers, so if you’re truly using them to erase, they won’t stay pretty for long (or rub the eraser on blank paper to clean it). The eraser doesn’t break or wear down quickly either. Even after some rigorous erasing, the pink shark’s chin was still intact!
There’s no stated age range for this kit, but I think it would be good for ages 6 & up. However, because the clay starts out dry and crumbly, younger kids might have a difficult time handling it on their own. But once the clay gets to Play-Doh consistency, it’s fine. Also (and it says this on the kit) the clay could stain “certain finishes” and should be kept away from “carpet, clothing, and other porous surfaces.”
It’s sky-high adventure at a our steampunk story time! These amazing airships with matching goggles are a cinch, thanks to our ready-made templates and a few sparkly extras!
Starting from the folded end, make four, 4.25″ long cuts. Each cut should end about an inch from the end of the paper. These will form the “struts” of your airship’s framework.
Unfold the poster board and flip it over. Currently, your struts have 1 central crease. You’re going to need to add 2 more creases on each strut (one on either side of the central crease). The new creases should be about 2.5″ away from the central crease.
Crease all the struts, then circle the poster board and staple both ends. Your airship framework should now look like this:
Punch four holes in one of the struts. This is where your airship’s basket will attach later.
Now for the balloon! Open, then crumble, a paper bag. The more wrinkly the bag, the better it looks! Keeping the bag crumpled, slip it between the struts. Gently fluff the bag to fill out the framework.
I have to say, that’s got to be the weirdest blog photo yet. And that’s saying a lot. Come to think of it, doesn’t it look a bit like a steampunk asthma inhaler?
You’ll notice that the airship in the above photo has a hanging loop at the top. That’s a 9″ piece of twisteez wire circled around the top strut. Secure the loop to the underside of the strut with tape.
If you’re using a bucket, it helps to stick a little picture of the item on the front, for kids who are too short to lean over and peer inside.
These buckets are great for organizing art supplies. I found them in the bulk candy section of Party City when I was researching red buckets for 
To make goggles, simply color a pair from the template, punch holes on the ends, and knot a 17″ piece of twisteez wire through both holes. Adjust for size, and perch the goggles on top of your head like a headband. Some kids, however, cut holes in their goggle’s eye pieces, which were incredibly adorable. Look at this duo!