This winter, I posted a sneak peek of a Cinderella dress created by local high school junior, Vicky Gebert. The dress was constructed of bubble wrap, trashcan liners, drinking straws, t-shirt bags, forks, blue cellophane lace, Styrofoam, and chicken wire. It looked utterly amazing.
Vicky’s dress was the centerpiece of a Cinderella Story: Make a Princess Dress program our library hosted last weekend. Kids were invited to channel their inner godmothers and create a dress out of art supplies (including supplies you might not immediately consider when planning a grand night out).
If you can’t wait to see some of the creative dresses, scroll past the instructions and let the fashion show begin. Otherwise, here are instructions for building your own princess dress!
For the dress base, you’ll need:
- A 11″ x 28″ piece of poster board for the bodice
- A 4″ x 28″ pieces of poster board for the skirt sash
- 4′ piece of ribbon for the bodice
- 2′ piece of ribbon for the skirt sash
- 2, 20″ pieces of tulle ribbon for shoulder straps
- Hole punch
I used black poster board to make the example dress (it shows up better in photos), but for the actual program, the bodice and skirt sash were made of white poster board. Definitely use the thicker variety of poster board (i.e. 6-ply) because it’ll hold up to all the art supplies you’ll be adding later. I also used 3/8″ white ribbon. It was easier to lace that particular width of ribbon through the punched holes without tearing the poster board. The tulle ribbon I used was 3″ wide to allow easier threading as well.
The Nearly New Shop, a local thrift and consignment store, was kind enough to loan us a dress mannequin for the program. It really helped to have the dress base on display so grown-ups could see what the final product should look like.
OK, ready to get started? First, wrap the largest piece of poster board around your upper body until both ends almost touch behind your back. Trim with scissors if the bodice is too long, cuts into your armpits, or if you want to create an unusual neckline.
Use a hole punch to make 5 matching pairs of holes down the back of the bodice
(our holes are marked with white rings in the photo so you can see them better).
Lastly, your shoulder straps! Slip on the bodice and adjust it to the right height on your chest. Punch a hole in the front of your bodice, directly underneath your shoulder. Punch a matching hole in the back. Thread a 20″ piece of tulle ribbon through the hole in the front and knot securely. Pull the tulle ribbon over your shoulder and thread through the hole in the back. Knot tightly and cut off any excess. Repeat on the other side. The finished straps should look like this:
Now that you know your dress fits, I recommend unlacing the bodice and the skirt sash and laying them flat for decorating. This is especially useful for the skirt sash. It’s easier to make a huge fluffy skirt on a flat surface than a curved surface.
Here are the art supplies we used at the program:
- Tissue paper (in 20″ x 26″ sheets)
- Construction paper (in 12″ x 18″ sheets)
- Bubble wrap
- Pink and blue cellophane lace
- Tissue paper circles
- Pastel crepe paper streamers
- A selection of iridescent fabric shapes
- A selection of curling ribbon, including gold curling ribbon
- White baking cups
- Some fabric flowers
- A selection of sparkle stems
- White drinking straws
- White 6″ circular doilies
- Gold and silver embossed foil seals
- A selection of small feathers
- A selection of embossed foil paper
- Gold and silver metallic tie cord
- A selection of large gemstones
- Clear trash can liners
- Costume jewelry donated by library staff (see more about that program here)
- Scissors, stapler, tape, packing tape, glue dots, glue sticks for construction
- Markers for decorating
- Hot glue
What can I say? We had a tremendous time! The kids not only made dresses, but matching crowns, wands, accessories, hairpieces, and jewelry. It was wonderful.